Cottingley Plasterers for Houses and Flats
From the houses along Cottingley Drive to the flats in the tower blocks on the hill, we skim, patch and cover old textured ceilings for Cottingley homes. Work is planned around family routines and kept clean.

Cottingley · LS11
Post-war houses and tower blocks on the hill
Cottingley in south Leeds is mostly post-war housing, built as a planned estate on the slope above the M621. There are semis and short terraces along Cottingley Drive and the roads around it, plus the tower blocks that stand out on the hilltop. Construction varies. Some houses have brick cavity walls with a traditional sand and cement backing and a gypsum finish, while others use concrete or system-built methods with plaster applied directly to the inner face.
The flats in the towers have concrete walls and ceilings, which behave very differently from brick. Plaster on concrete relies on a good bond, and when that bond fails you get hollow patches that sound drummy when tapped. Down the hill, towards the streets near Cottingley station, many homes have been improved over the years with new kitchens, bathrooms and windows, each leaving its own round of patched plaster that eventually needs pulling together with a proper skim.
Textured ceilings, cracks and tired walls
Plenty of Cottingley homes still have textured coatings on ceilings or walls, applied in the decades when that finish was fashionable. Older Artex-type coatings can contain asbestos, so we always arrange for a sample to be tested before anything is disturbed. Our usual approach is to seal the surface and skim over it, or overboard with plasterboard and then skim. We never sand or scrape it off. Either method leaves a smooth, modern ceiling without releasing dust.
Walls show their age in other ways. Cracks above doors, bumpy patches from past repairs and corners chipped by years of family life are all typical. A fresh skim over sound backing plaster makes a room look new. Where the backing has come loose from the wall, we cut it out and replaster that area first. Any patches of damp or mould need their cause put right before we plaster, since we do not offer damp treatments.
Fitting the work around home and family
Most jobs here are in lived-in homes, so we plan them that way. We clear and sheet one room at a time where possible, protect carpets and stairs, and tidy up before leaving each day. A skim on a single bedroom or ceiling is often done in a day, though it needs time to dry before decorating. We will tell you how long to wait and how to treat fresh plaster before painting.
For flats in the tower blocks, we ask about lift access and where we can unload, and we keep landings clear for neighbours. If you rent, check with your landlord or housing provider about what work you are allowed to arrange. To get started, contact us with a short description or a few photos. We will book a free visit, look at the rooms and send a written quote.
Services
Most asked-for in Cottingley

Skimming & reskimming
A thin, hard new face on walls and ceilings that are sound underneath but look tired, patched or lumpy.
See the service
Artex covering & removal
Swirls, stipples and peaks made flat again.
See the service
Patch & crack repairs
Holes left by the electrician, cracks over doorframes, knocked corners and the patch where the old boiler used to be.
See the serviceAlso in Cottingley
Everything else we do
FAQs
Plastering in Cottingley: questions
Can you get rid of the Artex on my Cottingley ceiling?
We arrange for the coating to be sample-tested first. In most Cottingley homes the best option is to seal it and skim over, or fix plasterboard over the top and skim. Both give a smooth finish without sanding or scraping the old texture.
Do you plaster flats in the Cottingley tower blocks?
Yes. We check lift access and unloading points before the day, protect communal areas and keep noise and dust to a minimum. If you are a tenant, it is worth confirming with your landlord or housing provider before booking any work.
Why does my wall sound hollow when I tap it?
That usually means the plaster has lost its bond with the wall behind it. On concrete or brick, the loose area is cut out and replastered so the new finish is firmly fixed. We test the wall on the visit and mark out how far the problem goes.
How soon can I paint after a skim?
Fresh plaster needs to dry fully, which usually takes several days to a couple of weeks depending on thickness, heating and ventilation. The first coat should be a thinned mist coat. We will give you specific guidance for your rooms when the job is done.